Shenzhen Merrytek Technology Co., Ltd.
Shenzhen Merrytek Technology Co., Ltd Intelligent Lighting Control
Add to Cart
KL12C-PV Multifunctional led driver 12W for LED downlight
【Product Feature】
【Parameter】
| Model | KL12C-PV | |
| Input | Operating Voltage | 198-264VAC 50Hz /60Hz |
| Rated Input Voltage | 220-240VAC 50Hz /60Hz | |
| DC Input Voltage range | 200-240VDC | |
| Input Cuttent | 0.07A Max. | |
| Input Inrush Current | <15A (Half current pulse width 100US) @230VAC | |
| Power Factor | ≥0.9C (@230VAC Full load) | |
| Total harmonic distortion | Typical: 20% (@230Vac Full load) | |
| Stand-by Power | ≤0.5W | |
| Efficiency | 83%Max. @230VAC (Full load) | |
| Wiring Method | Push terminal, wire cross section:0.75-1.5mm2 | |
| Output | Operating mode | Constant Current |
| Load type | LED | |
| Ripple requirement (Flickering or flickering-Free) | Flicker value: less than 2% for whole dimming range | |
| Start up time | <0.5s (@230Vac;Auxiliary has no output) | |
| No-load output voltage | 45VDC Max. | |
| Load output voltage range | 9-34VDC | |
| Full load output power | 12W Max. | |
| Load output current | 350mA(9-34V) 500mA(9-24V) 700mA(9-17V) | |
| Constant current/voltage Precision | Constant Current Precision ±5% | |
| Wiring method | Push terminal, wire cross section:0.5-1.5mm2 | |
Control Method | Primary PUSH Dimming | Primary PUSH dimming (Max.lead length:100M) |
| 1-10V Dimming | 0-10V dimming(Port current＜1MA) (Max.lead length:20M) | |
| Dimming Range | 2%-100% | |
| Primary PWM Dimming | 0-10V port PWM dimming (3KHZ-8KHZ) | |
| Potentiometer | Yes, 100kΩ | |
| Exception Protection Requirements | Output over temperature protection | Yes, without self recovery function(Can be inquired) |
| Output short circuit protection | Yes, without self recovery function(Can be inquired) | |
| Operating Environment | Operating temperature/ humidity | -25℃~50℃ Humidity:85% (Non-condensing) |
| Storage temperature/ humidity | -40℃~80℃, Humidity:10%–95% | |
| Max. case temp(Tc) | 85℃ | |
| Safety & EMC | EMC standard | EN55015 EN61547 EN61000-3-2 EN61000-3-3 |
| Safety standard | EN61347-1 EN61347-2-13 | |
| Certification | CE | |
| Withstand voltage | 3750Vac, 5mA, 60s (Input “L N”- Output “SEC”) | |
| Others | Degrees of protection | IP20 |
| Type of protection | Class II | |
| Installation type | Independent installation | |
| Installation dimension | 88*52*25mm | |
| Blackout memory function | Yes, PUSH blackout memory | |
| PUSH dimming synchronization | 30 units . | |
| Packaging requirement | white box+ Instructions Clapboard Outer Carton(K=A) | |
| Weight | 80g | |
| Life | 50000h @Ta full load | |
| Note: All parameters are tested at the input voltage of 230Vac and 25 degree environment unless specified. | ||
【Dimension (Unit:mm)】
【Wiring Diagram】
Fig. A Push Dimming OR Corridor function |
Fig. B 0-10V |
【Current Gear Setting】
| Current | voltage | J1 | J2 |
| 350mA | 9～34V | - | - |
| 500mA | 9～24V | SHORT | - |
| 700mA | 9～17V | SHORT | SHORT |
【Derating】
【Dimming Curve】
【ON/OFF & Description of Dimming Operation】
A. Brief push switches (< 1 s), LED driver ON or OFF. The brightness returns to the last dimming value.
B. Press and hold the PUSH switch (1S~8S), the LED driver can achieve dimming; After pressing it again, the light changes in the opposite dimming directions.
C. Push dimming has power-down memory and brightness memory.
D. Dimming synchronization:
LED driver can synchronize to a 50% dimming level with a 15-second hold the push.
E. Turn on and off fade times:Brief push to turn off the lights,Press and hold the PUSH switch, the light will turn on and brighten. The hold time will be saved as fade times.
F. Corridor function: PUSH has an L signal greater than 60S, enter the corridor function, 100% brightness, 20% brightness, wait for 60S, and then turn off the lights. Brief push switches 5 times to exit the corridor function.
G. Pushbutton with indicator lights are not allowed.
【Matters Needing Attention】