【Product Features】
- Casambi Bluetooth mesh networking was adopted, casambi App was used to design parameters And set application scenarios,DALI Microwave sensor
- Conform to new ERP standards; low stand-by power.
- 5.8GHz microwave license-free ISM wave band; bulk order are compliant with RED&TUV&DALI-2 approval.
- Compact size design, can be built-in most of light fixtures.
- Input and output terminals are convenient for connecting.
- Five year warranty
【Parameters】
| Input |
| Rated Voltage | 220-240VAC 50/60Hz |
| Stand-by Power | ≤0.5W |
| Surge Test | L--N: 1kV |
| Output |
| Output Control | √DALI-2signal |
| Sensor Parameter |
| Operating Frequency | 5.8 GHz ±75MHz, ISM wave band. |
| Transmitting power | 1mW Max. |
| Detecting Radius | Ceiling installation 3m height: 1m/s ≥ 2.5m, 0.3m/s ≥ 3.5m
Test condition: Product setting 100% sensitivity, 60㎡indoor open space |
| Mounting Height | 3m(6m Max) |
| Sensor sensitivity | Casambi App setting |
| Hold time | Casambi App setting |
| Daylight Sensor | Casambi App setting |
| Wireless parameters |
| BLE Module | Casambi Bluetooth |
| Working frequency | 2.402-2.480GHz |
| Transmitting power | +7dBm(max) |
| Transmission distance | 20m(Visible distance) |
| Fixture ID | 35480 |
| Environment |
| Operating Temperature | -25~60°C |
| Storage Temperature | -40℃~80℃, Humidity: ≤85%(Non-condensing) |
| Maximum Shell Temperature (Tc) | 80℃ |
| Certificate Standard |
| Certificate | CE, RED, TUV |
| Environmental Requirement | Compliant to RoHS 2.0, Reach |
| IP Rating | IP20 |
| Product Category | Class Ⅱ |
| Other |
| Wiring | Press-in type terminal block, wiring 0.5-1.5 mm2 |
| Installation | Built-in |
| Package | Bubble bag + Clapboard + Carton(K=A) |
| Net Weight | 40.2±3g |
| Lifetime | 5 years warranty @Ta |
【Product Information】
【Installation Instruction】
| Note: |
When installation, please pay attention to the front of microwave antenna is not allowed to be blocked by metal.
The AC incoming line needs to keep a distance of more than 10mm from the BUCK inductance, Otherwise it will cause conduction to fail. As shown in the following figure. |
【Detection Range】
【Initialization】
After power on, the sensor automatically turns on light to 100% brightness and turns off light after 10 seconds. During initialization, sensor is not able to detect movement.
【Default setting】
Sensitivity: 100%, Hold time: 5s, Daylight sensor: Disable
【Application Notice】
- Sensor should be installed by a professional electrician. Please turn off power before installing, wiring, or setting the DIP switches.
- Microwaves cannot penetrate metal. Do not place product in a closed or a half-closed metal lamp. Neither metal nor glass is not allowed to cover above the product. If antenna needs to pass through the metal plate, please ensure that the top of sensor is close to the metal plate.
- The installation spacing between sensors is recommended to be greater than 2m. Keep it away from wireless devices such as switches and routers, and the installation spacing between sensors and routers is recommended to be greater than 2m. The antenna surface of the microwave sensor should be away from the input AC and output DC to avoid low/high frequency signals affecting the normal operation of the microwave sensor antenna.
- Sensitivity area is related to moving speed of objects, size of moving objects, mounting height, mounting angle, working environment, reflecting materials and etc.. Given detecting area is typical value that was measured by 165cm high testers in an indoor open environment.
- This model is suitable for ceiling installation. If wall installation is used, the microwave sensor sensing detection area is greatly increased, and it may cause the phenomenon of microwave penetrate wall or the light not going out. So please adjust the sensitivity to 10%. If the sensitivity 10% can not be used, please avoid to the wall installation or ask the manufacturer for technical support.
- The daylight thresholds are measured on a sunny day without shadow and in an ambient light diffuse reflection status. Different environment and climate cause different brightness values that daylight sensor measures.
- Sensor should not be covered or hided by metal, PCB, LED tray etc..The spacing between the sensor antenna and surrounding materials should be greater than 5mm. There should be no metal or PCB tracks near the sensor antenna, above or below it. The recommended thickness of cover is 2mm, and keep the spacing between the sensor antenna and cover is greater than 3.2mm.
- Vibration signals will be regarded as moving signals to trigger sensor. Installing sensor should be away from the object that vibrates for a long time, such as large metal equipment, pipes, air conditioning outlets, exhaust vents, smoke exhaust machine ports, shaking fans, etc. Pets in detecting area may cause false trigger.
- The antenna surface of microwave module should be away from input AC, output DC, rectifier bridge, transformer, switch tube and other high-power devices to avoid high frequency signals affecting the normal operation of microwave sensor’s antenna.
- Sensor is for indoor use only. The waterproof effect for outdoor or half-outdoor use will be affected. Wind, rain, and moving objects may cause false triggering. When the sensor is installed in a metal lamp, a metal reflective surface or a small enclosed environment, the microwave will be reflected many times and cause false triggering, please reduce the sensitivity or ask the manufacturer for technical support.
- When ambient temperature is over 80'C, over temperature protection may be triggered (automatic recovery after cooling)
- For the new installation environment, it is recommended to test 5pcs samples before installation.
