Shenzhen Merrytek Technology Co., Ltd.
Shenzhen Merrytek Technology Co., Ltd Intelligent Lighting Control
Add to Cart
1-10V Dimmable Microwave Motion Sensor For Tri-proof Light, 6m Max Mounting Height, With Sync ON/OFF Function
1. Features
2. Parameters
| Input | Operating voltage | 108-305V AC 50Hz/60Hz |
| Rated voltage | 120-277V AC | |
| Stand-by power | ≤0.5W(230Vac) | |
| Output | Working mode | ON/OFF 1-10V dimming |
| Type of load | White woven light/power supply /1-10V LED light | |
| Load capacity | 120Vac 400W(inductive or resistive) 220Vac-240Vac 800W(inductive or resistive) 277Vac 1000W(inductive or resistive) | |
| Max.surge capacity | 30A (50% Ipeak, twidth =500uS, 230Vac full load, cold start); 60A (50% Ipeak, twidth =200uS, 230Vac, full load, cold start) | |
| Dim interface | 1-10V Dimming | Available |
| Syn control | Available(Can sync for on-off function,can’t sync for 1-10V dimming ) | |
| Sensor parameters | Operating frequency | 5.8 GHz ±75 MHz,ISM band |
| Transmitting power | 1mW Max. | |
| Detection Area | 25%/50%/75%/100%(by two DIP switches) | |
| Hold time | 5s/30s/90s/3min/20min/30min(by three DIP switches) | |
| Stand-by dim Level | 10%(1.4-1.6V)/20%(1.9-2.1V)/30%(2.9-3.1V)/50%(4.9-5.1V)(by two DIP switches) | |
| Stand-by Period | 0S/5S/5min/10min/30min/1h/+∞(by three DIP switches) | |
| Daylight Sensor | 2 lux/5Lux /10Lux /25Lux /50Lux /100Lux /Disable(by four DIP switches) | |
| Detection Range (100% Sensibility Radius) | Surface mounting 3m height:0.3m/S ≥3.5m,1m/S ≥2.5m Horizontal mounting 2m height:0.3m/S ≥8m,1m/S ≥4m | |
| Mounting height | 3m(6m max) | |
| 3db beam Angle
| 80°@XZ plane 96°@YZ plane | |
| Operating envrionment | Operating Temperature | -25℃~70℃ |
| Storage Temperature/humidity | -40℃~80℃ humidity:≤85% (non-condensation) | |
| Certificate Standards | Safety(LVD) standards | EN61058-1,EN61058-1-2, |
| lightning surge | 1KV(L/N,EN61000-4-5) | |
| EMC standards | EN61058-1,EN61000-3-2,EN61000-3-3,EN62479, EN301489-1,EN55015,EN300440 | |
| Environmental Requirement | Compliant to RoHS | |
| Certificate | CE, RED,TUV | |
| Others | Input/Output(connector/wiring)specification | Press-in terminals wire diamter:0.75-1.5mm2 |
| Installation Requirement | Built-in | |
| Installation Dimension | 180*50*30mm | |
| Package Requirement | Bubble bag+ Clapboard+ Carton(K=A) | |
| Net weight | 75g | |
| Life time | 5 years warranty @Ta 230V full load |
3. Parameters
1. On-off function(Stand-by Period “0s”)
2. 2-step dimming function(Stand-by Period“+∞”)
3. 3-step dimming function(Stand-by Period“5s/5min/10min/30min/1h”)
4. Dimension (mm)
| 1 | 2 | ||
| Ⅰ | ON | ON | 100% |
| Ⅱ | ON | - | 75% |
| Ⅲ | - | ON | 50% |
| Ⅳ | - | - | 10% |
| 3 | 4 | 5 | ||
| Ⅰ | ON | ON | ON | 5S |
| Ⅱ | - | ON | ON | 30s |
| Ⅲ | ON | - | ON | 90S |
| Ⅳ | - | - | ON | 3min |
| Ⅴ | ON | ON | - | 20min |
| Ⅵ | - | - | - | +∞ |
3. Stand-by Period
| 6 | 7 | 8 | ||
| Ⅰ | ON | ON | ON | 0S |
| Ⅱ | - | ON | ON | 5S |
| Ⅲ | ON | - | ON | 5min |
| Ⅳ | - | - | ON | 10min |
| Ⅴ | ON | ON | - | 30min |
| Ⅵ | - | ON | - | 1H |
| VII | - | - | - | +∞ |
4. Daylight Sensor
| 1 | 2 | 3 | 4 | ||
| Ⅰ | - | - | ON | ON | 2Lux |
| Ⅱ | - | - | - | ON | 5Lux |
| Ⅲ | - | ON | ON | - | 10Lux |
| Ⅳ | - | - | ON | - | 25lux |
| Ⅴ | - | ON | - | - | 50lux |
| Ⅵ | ON | - | - | - | 100lux |
| VII | - | - | - | - | Disable |
* When set to Disable, the sensor will turn on the light when it detects movement, regardless of whether the light is sufficient.
* Daylight threshold value is the typical value under the condition of sunny environment, no shading, diffuse reflection of ambient light.
5. 1-10V(Stand-by DIM Level)
| 5 | 6 | Brightness% | |
| Ⅰ | ON | ON | 50% |
| Ⅱ | - | ON | 30% |
| Ⅲ | ON | - | 20% |
| Ⅳ | - | - | 10% |
1) The sensor should be installed by a professional electrician. Please turn off the power before installing, wiring, changing the setting of the DIP switch.
2) Microwave cannot penetrate metal, please avoid installing the product in closed or semi-closed metal lamps, and ensure that there is no metal or glass shield above the product; If the antenna must pass through the metal plate, ensure that the top of the sensor is close to the metal plate.
3) The installation distance between microwave sensors is recommended to be greater than 3m, and should be far away from switches, routers and other wireless devices to avoid radio interference. The installation distance between both is recommended to be greater than 2m; The antenna surface of the microwave sensor must be far away from the input AC and output DC to avoid interference from low/high frequency signals.
4) Long-term vibration equipment or moving objects should be avoided around the microwave sensor. The vibration signal generated will be regarded as mobile signal triggering induction. If a pet passes by in the test area, the sensor may be triggered.
5)This product is suitable for indoor installation,if for semi-outdoor or outdoor installation, wind and rain may be regarded as a mobile signal trigger induction; When the sensor is installed in a metal lamp, metal reflective surface, or a narrow enclosed environment, the microwave will be reflected repeatedly and cause false triggering. Please reduce the sensitivity or contact the manufacturer for technical support.
6)This model is suitable for ceiling installation. If wall installation is used, the microwave induction detection distance will be greatly increased, which may lead to microwave penetration through the wall or the lamp will not be off. Please adjust the sensitivity by 25%. If 25% cannot be used, avoid wall installation or contact the manufacturer for technical support.
7)Product specifications and parameters may be optimized without prior notice.
8) The light sensitivity threshold is in a sunny environment, no shadow and ambient light diffuse reflection.Lux level detected by sensor could be different in different period and climate condition.
9) Product detection range is related to the moving speed of the object, the size of the object, the installation height of the product, the installation angle, the installation environment, the material of the reflection and other factors.
10) The detection distances given in the specifications are typical values, which are obtained by testers in an indoor open environment of 165cm/65kg.
11) Do not put the sensor near high-density objects, such as metal, glass, mixed walls, etc., because the sensor may trigger incorrectly.
12) Sensor parameters may need to be reconfigured in different installation environments. Please refer to the above instructions or contact the manufacturer.